Seeing other brides’ ideas and what has been done at other weddings is enough to inspire any bride-to-be…and keep you glued to your computer screen for hours on end. To help you out, here is a list of some can’t miss surprises for your groom, your bridal party, your guests and even for yourself. From games to honoring the people you love.
1. A live wedding painter to capture your ceremony/reception space and your guests.

2.Arrange ceremony seats in a circular pattern around the couple so that everyone can see.

​5. Put photos of yourselves at different ages corresponding to table numbers for your guests to enjoy.

9. Compile addresses of all of the guests at your wedding

10. ​Leave fun facts about yourselves on the tables.

11. ​ Honor guests that aren’t in your wedding party (or can’t be at your wedding).

12. Pin something sentimental on your bouquet

17. Have guests sign a calendar with their birthdays, anniversaries, etc.

18. Guests throw darts at balloons filled with paint attached to a canvas. You keep the art.

19. Take a picture of the rings with a newspaper from the day of your wedding.

20. Incorporate cake pops that match your wedding invitations

8.Copland’s Fanfare for the Common Man
During World War II, the conductor of the Cincinnati Orchestra asked Aaron Copland to create a fanfare to be used to introduce concerts. The conductor had suggested a salute to the common soldier, after similar pieces created by English composers during the First World War, but Copland, instead, sought to make a salute to the Four Freedoms (freedom from fear, want, religion and speech & expression).
​Finally, he settled on making a salute to the common man. At the orchestra leader’s suggestion, it premiered during income tax season in 1943. Copland later turned the Fanfare into the theme for the fourth movement of his Third Symphony. The now-familiar Fanfare can be heard at rock concerts, the Olympics and political campaign events.

1. Mamita´s Beach Club
Mamita´s Beach Club is undoubtedly the Mexican Caribbean beach club par excellence. With 650 ft. of the best beach in Playa Del Carmen, Mamita's Beach Club provides services and comforts of first quality to their guests: modern restrooms equipped with air-conditioning, showers, kids pool, an area with massage service, and 300 deck chairs and 100 beach umbrellas for rent, towels as well,  parking lot with valet parking, Wi-Fi service and private security. This is the perfect place  with lounge music and very nice cocktails.

7. Coralina Daylight Club 
Coralina Daylight Club takes notes from places like Ibiza, Spain where they started the party early and enjoy DJ’s and a club like atmosphere only this time when the sun is out. People do like to have a good time during the day and this is kind of a new concept for Playa Del Carmen.  Coralina has upped the game and created a beach club that is less about being in the sand and more about being near the pool and drinking with friends while listening to electronica and dance music.
​
This club is not going to be for everyone.  It is a place to be seen and see others. Enjoy the atmosphere here and music.

2. “View Of The Sea At Scheveningen” By Vincent Van Gogh
On 7 December, 2002, at around 8:00 AM, two men climbed onto the roof of Amsterdam’s Van Gogh Museum and broke through into the building. The thieves only took two paintings—“View of the Sea at Scheveningen” and “Congregation Leaving the Reformed Church in Nuenen,” both painted between 1882 and 1884. This period represented the peak of Van Gogh’s artistic achievements and the paintings are estimated to have a combined value of $30 million.
​
According to the museum gallery page, “Van Gogh painted this picture on the spot, at Scheveningen, a beach resort near The Hague. He had to fight against the elements: the gusting wind and flying sand, which stuck to the wet paint. Most of this was later scraped off, but a few grains can still be found in some of the paint layers.” Two suspects were arrested in 2004 and later sentenced to up to four-and-a-half years, but the paintings have yet to be found. The museum currently offers a reward of €100,000 for information on their whereabouts.

5. ​"The Pigeon Aux Petits Pois" by Pablo Picasso
One of the strangest art thefts in history took place in Paris, France about May 20, 1911 7:00 masterpiece "The pigeon pea small" 2010, Pablo Picasso (Le pigeon aux petits pois) was one of five paintings estimated to a total value of approximately € 100 million, stolen from the Musée d'Art Moderne de la Ville de Paris. One broken window and a broken padlock were found at the crime scene. The thief had the dexterity to quickly and thoroughly remove the paintings from their frames rather than use a knife to cut them out. security images revealed that the burglary was a work of a man rather than a team of robbers. A man said to be the lone thief was caught and sentenced in 2011, and later said he had panicked and threw paint in the trash shortly after stolen. Many people have expressed doubts about the story of the thief from today and the paint is still nowhere to be found.

The violin is the most modern embodiment of stringed musical instruments played with a bow. Like the guitar and other plucked string instruments, bowed instruments date from antiquity. Although its precise origins are not completely understood, it is probable that the violin evolved during the mid-16th century in Northern Italy. In addition to perhaps being the maker of the first true violins, Andrea Amati (ca. 1500-1577) was the patriarch of the Cremona school of violin making.

During the next 150 years, other members of the Amati family and their followers, who included Antonio Stradivari  and Bartolomeo Giuseppe Guarneri , brought the violin to its highest level of perfection both as a musical instrument and as a work of art.

During the 17th century, violin making spread to all of the other countries of Europe and, in the 18th and 19th centuries, to the rest of the world. Although violins have been and are being turned out in large numbers by factories in Europe and Asia, most fine violins are handmade by individual craftsmen using essentially the same methods employed by classical Italian makers several hundred years ago.

Tools:
Most of the tools required for violin making are the same as those used for most types of hand woodworking and carving: planes, chisels, gouges, knives, saws, and scrapers. In addition, a few specialized tools are needed. These include a thickness caliper, small curved bottom "thumb" planes, purfling groove cutter, peg hole reamer and matching peg shaver, bending iron, clamps of various types, and patterns. Many violin makers take pride in making some of their own tools. Indeed, one of the keys to success as a violin maker is developing the skills associated with making, using, and maintaining sharp edged tools.

Raw Materials:
The back, sides (ribs), and neck of the violin are most often made of matching quarter-sawn (cut along the radius of the log) maple. There are many species of maple, growing in different parts of the world, which are suitable. The criteria for selection include the straightness of the grain, the density and the figure of the wood, all of which contribute to the tonal characteristics and visual beauty of the finished instrument. The top of the violin is made of quarter-sawn spruce. The internal parts of the violin—the corner and end blocks and the linings—are usually made of spruce or willow, while purfling can be made of many different woods and/or "fiber" (thick paper or cardboard). The fingerboard is made of ebony, the bridge is maple, and the other fittings (pegs, tailpiece, chin rest) are ebony, rosewood, or boxwood. Rather than making these items from scratch, they are usually purchased in a finished or semi-finished form and customized or installed by the maker.

The Manufacturing  Process 
The ribs

• 1 The first step in making a violin is to make the sides (ribs) from which the outline of the top and back will be taken. The ribs are constructed on an "inside" mold, which is a wooden form about 15 to 18 mm thick cut to the exact outline of the inside of the violin. Pieces of wood for the corner and end blocks are cut to approximate size and temporarily glued to cutouts on the mold at the proper locations. With the aid of a pattern and using gouges and files, the blocks are trimmed to the final shape of the inside contour of the violin. Slices of maple slightly wider than the height of the ribs, which are about 30 to 32 mm for a violin, are cut and planed to a thickness of 1 mm. Pieces are bent to the shape of the mold and blocks using a heated metal form. After trimming to slightly longer than the final length, the ribs are glued. To hold the ribs in place until the glue dries, countermolds shaped to match the outside contours of the ribs at the corners and ends are used. Pressure is applied by clamps or wrapping with string. Care must be taken to avoid gluing the ribs to the mold, which must be removed in a subsequent step. The ribs are glued in sequence starting with the middle bouts, which must be trimmed to final length at the corners before the upper and lower ribs can be added. The linings, strips of willow or spruce about 2 by 8 mm, are bent to shape using the bending iron, cut to length, and glued to the inside of the ribs. The corners are trimmed to their final shape, and the top and bottom surfaces of the ribs, linings, and blocks are planed and filed to be level at the final height.

Top and back

• 2 The tops of violins are almost always made from a wedge of wood which is cut or split, with the edges of resulting pieces glued together. This joint, for which the pieces must fit with absolute perfection, then becomes the centerline of the top. Maple for the backs of violins is treated the same way to make a two-piece back, however, it is possible to find a piece wide enough to make a one-piece back. Planing the wood to create a perfect center joint is an exacting task. After the pieces have been planed to fit well—as seen by holding the pieces together in front of a light—the edge of one piece is coated with chalk and rubbed against the mating edge. The areas in which chalk is transferred from one piece to the other identify places which must be shaved slightly with the plane to perfect the fit. This chalk fitting procedure is repeated until the fit between the two pieces is perfect, after which they are glued together and clamped. After gluing the center joint, the flat side of the back and top are planed flat. The ribs are placed on this flat side; a tracing around the ribs enlarged by 3 mm establishes the outline of the top or back (a 20 mm square is added at the top of the back for the button). These outlines are cut out using a bow or coping saw; many modern violin makers use a power band or scroll saw.The outside arching of the top and back are next carved using gouges, thumb planes, and scrapers for the final smoothing. Five transverse and one longitudinal arching guides are consulted frequently as the plates take shape. The arching guides, which are different for the top and back, plus the out-line embodied in the mold, determine the design or model of the instrument. Most modern makers follow or copy the designs of great makers such as Stradivari or Guameri, while some have evolved their own. Next the interior sides of the top and back are carved out. The final thicknesses of the wood has a major influence on the acoustic performance of the finished instrument, and there are many systems in use for arriving at the optimum distribution of thicknesses. In general, most methods involve testing the resonance frequencies of the plates by tapping, flexing, or exciting them with sound, coupled with measurements of the thickness of the plate at many locations using a graduation caliper. Then, depending on the results and on the desired outcome, wood is gradually removed from various locations. Usually, makers seek to establish certain relationships, e.g. octaves, between the various resonances of each plate and between the two plates. Typical thicknesses of a finished back are 4.5 mm at the center decreasing to 2.4 to 2.5 mm in the upper and lower bouts. The thicknesses of the top are more uniform: about 3 mm over-all, and perhaps slightly thicker between the soundholes in the area of the soundpost.

Completing the top

• 3 The outline of the sound holes is transferred to the top, and these are cut out using a sharp knife; some makers use a punch or drill to cut the round holes. The bassbar is made of very straight grained, quarter-cut spruce (much like the top). The area where it fits is outlined on the side of the top, and the rough blank is trimmed to precisely fit the arching. The chalk-fitting method is employed again in this step. The bar is then glued in place and trimmed to its final contour. This again involves testing the resonance of the top, which was altered by the cutting of the sound holes as well as the addition of the bassbar.

Completing the body

• 4 The mold is now removed from the rib assembly by loosening the temporary glue bonds of the blocks to the mold. The top and back are then glued to the ribs. The glue holding the back should be full-strength. Thinner, weaker glue is used for the top; this provides for easy removal if service or adjustment is necessary, and will allow the seams to open in extremes of humidity and temperature rather than produce cracks in the wood itself. The groove for the purfling is marked a precise distance from the edges using a purfling cutter. The groove is deepened with a sharp knife and the wood in the groove removed with a purfling pick. The purfling strips, which can be bought ready or made by the violin maker, are bent to fit the groove using the bending iron. The pieces are then cut to the exact length, mitered to fit the corners, and glued in place. The channels which run over the purfling just inside the edges are cut with a gouge and blended into the arching with gouge, planes, and scrapers. Finally, the edge is rounded using knife, file, and perhaps sandpaper. (This is one of the only places in which sandpaper is used in the construction of a violin. All of the other surfaces should be finished with scrapers, which provides a crisp appearance to the workmanship and best reveals the beauty of the wood.)

The neck

• 5 A block of maple matching the back is squared on the sides and top with a plane. Next, the outline of the side view of the neck and scroll is traced on the quarter-cut side of the block. The wood outside the outline is sawed away. Patterns and outlines for the peg box, top surface of the neck, and the scroll are traced. A razor saw is then used to cut away wood around the scroll and neck outlines. Gouges and scrapers are used to finish the carving of the scroll, the details of which are one of the ways in which the violin maker expresses his individuality. The pegbox is excavated using chisels and gouges. The neck is cut to final dimensions using planes, knives, and scrapers. A mortise (cavity) to receive the neck is cut into the upper ribs, block, and top of the violin's body. The cut of the mortise and the root of the neck must be very precise, since the correct height and angle of the neck are critical to achieving a good tonal result. Chalk fitting is again employed. The neck is then glued into the mortise, and the final shaping of the heel of the neck and the button on the back is done.

Varnishing

• 6 There is a great deal of lore associated with the varnishing of violins. It has even been asserted that secret recipes are responsible for the extraordinary tonal characteristics of the old Italian violins. Regard-less of its possible effects on tone, it is certainly true that the varnish does serve other important purposes of beautifying the appearance and protecting the wood from wear, damage, moisture, and dirt. Thus the selection and application of varnish is vitally important. Because there are many types of varnish and working methods, the following rather general outline of finishing is provided:
  • The finished violin is hung up to age for a time (in some cases several months or more), and may be exposed to sunlight. This will cause the wood to darken and bring out its figure. Many makers use less time-consuming alternatives.
  • A sealer or pore filler is then applied.
  • The vamish is applied in several coats. This may include coats of clear vamish followed by additional coats of colored varnish. Vamish is essentially a coating consisting of resins, which may be natural substances (e.g. copal or seedlac) or man-made. Color is imparted to vamishes by adding pigments or dyes. The color of the individual coats may be varied to produce the desired appearance. Following the colored vamish, an additional coat or two of clear vamish may be applied to protect the layers underneath.
  • Since old-looking violins are more appealing to many players, some makers "antique" their instruments. The various methods of antiquing are usually trade secrets, and makers pride themselves on their individual results.
  • The surface of the fully dried vamish may be rubbed out using some combination of abrasives (pumice, rottenstone, fine emery paper, etc.) and polishes.
  • The part of the neck between the heel and the peg box is not varnished. Rather it is stained, sanded very smooth with fine emery paper and "french polished" (an application of shellac, and/or alcohol, and oil).

Fitting up

• 7 The top of the neck is planed flat, and the underside of the ebony fmgerboard is planed to fit and glued in place. The sides and top are finished with planes, scrapers and emery paper to be smooth and to have exactly the correct curvature. Gauges and straightedge are consulted frequently during this process. The ebony nut is cut to size, lightly glued at the top of the fingerboard, dressed to final shape, and grooves filed for the strings. A mortise is cut at the bottom of the violin into which is glued the ebony saddle. The pegs are shaved to the proper taper and diameter. Peg holes are drilled and reamed to match the pegs. Likewise, a hole at the bottom of the ribs is drilled, reamed, and fitted with the end pin.The bridge and soundpost are the last parts to be fashioned; their fit and position greatly affect the sound and playing qualities of the violin. Starting with a precut blank, the feet of the bridge are cut to fit the arching of the top at the proper position—between the nicks of the soundholes. The top of the bridge is cut to an arch which matches the curvature of the fmgerboard and provides the proper height of the strings. The front side (facing the neck) is planed down to a thickness of about 4.5 mm at the bottom and tapering from the middle to 1.5 mm at the top. Grooves for the strings are cut and filed using a gauge to establish their proper position and spacing. The soundpost transmits the vibrations of the strings to the back of the violin. It is cut from a round piece of straight-grained spruce about 6 mm in diameter. Its length and ends must be cut so that it fits precisely in the proper location inside the violin, about 3 mm behind the treble foot of the bridge. A gauge may be used to measure the approximate length of the sound-post, but the final fit is a trial and error process. The soundpost is inserted and its position adjusted through the soundholes using a special tool. The strings are now fitted into the tailpiece, extended over the bridge and wound on the pegs. Once all four strings are installed, they may be tuned up to pitch and the violin played for the first time. What follows will be a period of adjustment as the violin becomes accustomed to the tension of the strings and their vibration. Numerous adjustments to the position of the soundpost, the bridge, types of strings, and perhaps other factors are usually necessary to optimize the tonal characteristics and playability.

If you’ve been asked about the theme of your wedding, chances are music isn’t the first thing that comes to mind. But tunes are often a common thread early in a relationship and can hold a lot of sentimentality for many couples. That’s why  a musically themed wedding is a fantastic way to celebrate your love with family and friends. From sock hop to festival to rock concert, a music theme makes for a great way to show some personality with all sorts of touches.

1. Floral Guitar Decor: Add a folksy, Americana touch to a rustic wedding with guitars strewn with flowers. Everyone will be swooning over this romantic touch. 

4. Amp Dessert Table: Who says your theme can’t extend to your furnishings? Use speakers of varied heights to create a visually interesting dessert spread.

1. The tension of the 230-odd strings in a grand piano exert a combined force of 20 tonnes on the cast iron frame.

2. Robert Schumann would often plunge his hands into the entrails of a slaughtered animal to heal his ailments.

3. There are two skulls in Haydn's tomb. His head was stolen by phrenologist and a replacement skull was put into his tomb. In 1954, the real skull was restored but the substitute was not removed.

4. Rossini wrote the area "Di tanti palpiti" while waiting for some risotto in a Venice restaurant.
​
5. A single violin is made from over 70 individual pieces of wood.

6. According to his boasts in the opera, Don Giovanni seduced 1001 spanish, 640 italian,231 german,100 french and 91 turkish women.

​7. The London Symphony Orchestra was booked to travel on the Titanic's maiden voyage. But they changed boats at the last minute.

8. Baritone Leonard Warren died on stage at the Met in 1960 just as he had finished singing Verdi's "Morir , tremenda cosa".

9.Dogfish skin was often used in the 18th century to sand violins.

10. Soprano Dame Nellie Melba died from a skin infection after an unsuccessful facelift operation.

11. Russian cosmonaut Yuriy  Gagarin sang a Shostakovich song "My homeland hears",  over the radio on his first space mission.

12. During a performance of Boris Godunov at Sydney Opera House, a chicken fell off the stage... and onto a cellist.

13. Renaissance composer Orlande de Lassus was kidnapped many times as a boy because of his beautiful singing voice.

14. The most expensive opera costume of all the time was worn  by Adelina Patti  at Covent Garden in 1895. It was worth over £ 15 million.

15. Franz Liszt  received so many requests for locks of his hair that he bought a dog and sent fur clippings instead.

16. When he died, conductor Herbert von Karajan's wife, Eliette, inherited a fortune worth € 250 million.

17. Mozartkugeln' is one of the most popular chocolate brands in Austria. 

18. Havergal Brain's Symphony  No.1, the "Gothic", requires over 800  musicians to perform  including 82 string players.

19. Domenico Scarlatti composed his "Cat Fugue" after his cat, Pulcinella, walked across his keyboard. 

20.The Japanese world "Karaoke"  comes from a phrase meaning  " Empty Orchestra"